From Mehmet.Ergin at mam.gov.tr Wed Jun 1 01:16:50 2011 From: Mehmet.Ergin at mam.gov.tr (Mehmet Ergin) Date: Wed, 1 Jun 2011 11:16:50 +0300 Subject: [SAC-HELP] cutting sac files on time Message-ID: <9E88105FE4AC8C47BD6D00EB9831482F1F5B1596C1@posta.mam.gov.tr> Hi, I just want to cut sac files only by giving exact time. I use to sign to put T0 and then cut from T0 but always have problems to see exact peak to cut, so I just want to give exact time to cut without putting T0 . is it possible to cut files only by giving exact times. thanx ------------------------------------------ Mehmet ERG?N Do?. Dr. Ba?uzman Ara?t?rmac? [cid:image002.gif at 01CC204D.675A3F00] T?B?TAK Marmara Ara?t?rma Merkezi Yer ve Deniz Bilimleri Enstit?s? P.K. 21, 41470 Gebze Kocaeli T 0 262 677 2864 F 0 262 641 23 09 Mehmet.ergin at mam.gov.tr ----------------------------------------- Mehmet ERG?N Assoc.Prof. Chief Senior Scientist [cid:image002.gif at 01CC204D.675A3F00] T?B?TAK Marmara Research Center Earth Sciences Institute P.O. Box 21, 41470 Gebze Kocaeli TURKEY T +90 262 677 2864 F +90 262 641 23 09 Mehmet.ergin at mam.gov.tr ________________________________ Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya da kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi gizlilik y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki dosyalarda bulunan t?m fikir ve g?r??ler sadece adres sahip(ler)ine ait olup, T?B?TAK MAM bu e-posta i?eri?indeki bilgilerin kullan?lmas? nedeniyle hi? kimseye kar?? sorumlu tutulamaz Mesaj?n yetkili al?c?s? veya al?c?s?na iletmekten sorumlu ki?i de?ilseniz, mesaj i?eri?ini ya da eklerini kullanmay?n?z, kopyalamay?n?z, yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? g?nderen ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n ve bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in korunmas? konusunda garanti vermemekte olup, e-posta i?eri?ine yetkisiz olarak yap?lan m?dahale, vir?s i?ermesi ve/veya bilgisayar sisteminize verebilece?i herhangi bir zarardan da sorumlu de?ildir. This e-mail message, including any attachments, is intended only for the use of the individual or entity to whom it is addressed and may contain confidential, private information as well as the exemption from disclosure. All ideas and opinions in this message and attached files can only belong to the addressee(s) and TUBITAK MRC shall have no liability to any person with regard to the use of the information contained in this message If you are not the intended addressee(s) or responsible person to inform the addressee(s), you are hereby notified that; any use, dissemination, distribution, or copying of this message and attached files is strictly prohibited. Delete the message and notify the sender immediately. TUBITAK MRC do not warrant for the accuracy, completeness of the contents of this email and/or the preservation of confidentiality and shall not be liable for the unauthorized changes made to this message, viruses and/or any damages caused in anyway to your computer system -------------- next part -------------- An HTML attachment was scrubbed... URL: -------------- next part -------------- A non-text attachment was scrubbed... Name: image002.gif Type: image/gif Size: 1694 bytes Desc: image002.gif URL: From Mehmet.Ergin at mam.gov.tr Fri Jun 3 05:30:35 2011 From: Mehmet.Ergin at mam.gov.tr (Mehmet Ergin) Date: Fri, 3 Jun 2011 15:30:35 +0300 Subject: [SAC-HELP] cutting sac files on time Message-ID: <9E88105FE4AC8C47BD6D00EB9831482F1F5B159C71@posta.mam.gov.tr> Sent: Wednesday, June 01, 2011 11:17 AM To: 'sac-help at iris.washington.edu' Subject: cutting sac files on time Hi, I just want to cut sac files only by giving exact time. I use to sign to put T0 and then cut from T0 but always have problems to see exact peak to cut, so I just want to give exact time to cut without putting T0 . is it possible to cut files only by giving exact times. thanx - ________________________________ Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya da kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi gizlilik y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki dosyalarda bulunan t?m fikir ve g?r??ler sadece adres sahip(ler)ine ait olup, T?B?TAK MAM bu e-posta i?eri?indeki bilgilerin kullan?lmas? nedeniyle hi? kimseye kar?? sorumlu tutulamaz Mesaj?n yetkili al?c?s? veya al?c?s?na iletmekten sorumlu ki?i de?ilseniz, mesaj i?eri?ini ya da eklerini kullanmay?n?z, kopyalamay?n?z, yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? g?nderen ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n ve bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in korunmas? konusunda garanti vermemekte olup, e-posta i?eri?ine yetkisiz olarak yap?lan m?dahale, vir?s i?ermesi ve/veya bilgisayar sisteminize verebilece?i herhangi bir zarardan da sorumlu de?ildir. This e-mail message, including any attachments, is intended only for the use of the individual or entity to whom it is addressed and may contain confidential, private information as well as the exemption from disclosure. All ideas and opinions in this message and attached files can only belong to the addressee(s) and TUBITAK MRC shall have no liability to any person with regard to the use of the information contained in this message If you are not the intended addressee(s) or responsible person to inform the addressee(s), you are hereby notified that; any use, dissemination, distribution, or copying of this message and attached files is strictly prohibited. Delete the message and notify the sender immediately. TUBITAK MRC do not warrant for the accuracy, completeness of the contents of this email and/or the preservation of confidentiality and shall not be liable for the unauthorized changes made to this message, viruses and/or any damages caused in anyway to your computer system -------------- next part -------------- An HTML attachment was scrubbed... URL: From mplasencia at ogs.trieste.it Fri Jun 3 22:31:53 2011 From: mplasencia at ogs.trieste.it (Milton P. Plasencia Linares) Date: Sat, 04 Jun 2011 07:31:53 +0200 Subject: [SAC-HELP] cutting sac files on time In-Reply-To: <9E88105FE4AC8C47BD6D00EB9831482F1F5B159C71@posta.mam.gov.tr> References: <9E88105FE4AC8C47BD6D00EB9831482F1F5B159C71@posta.mam.gov.tr> Message-ID: <20110604073153.10566cc9zbdg770p@webmail.ogs.trieste.it> Hi Mehmet, You must to use the cut command, using in this way: sac> cut t0 t1 sac> read file sac> plot sac> synchronize sac> plot In the second plot you see the time windows of cut, the "exact" time depend of your sampling rate, in other words, if you have 100 s/s you cant cut for example to=0.00 to t1=10.00, remember that the independent variable is t in seconds, so your cut resolution is 1/100 of second. Try cut 0.01 10.00 and cut 0.02 10.00, small values no works. HTH, Milton ********************************** Milton P. PLASENCIA LINARES Dipartimento Centro di Ricerche Sismologiche Istituto Nazionale di Oceanografia e di Geofisica Sperimentale - OGS Borgo Grotta Gigante 42/C (34010) Sgonico - TRIESTE - ITALIA Tel: +39-040-2140136 Fax: +39-040-327307 E-mail: mplasencia at ogs.trieste.it ASAIN (Antarctic Seismographic Argentinean Italian Network) ********************************* Quoting "Mehmet Ergin" : > Sent: Wednesday, June 01, 2011 11:17 AM > To: 'sac-help at iris.washington.edu' > Subject: cutting sac files on time > > Hi, > I just want to cut sac files only by giving exact time. I use to > sign to put T0 and then cut from T0 but always have problems to see > exact peak to cut, so I just want to give exact time to cut without > putting T0 . is it possible to cut files only by giving exact times. > thanx > > - > > ________________________________ > Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya > da kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi > gizlilik y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki > dosyalarda bulunan t?m fikir ve g?r??ler sadece adres sahip(ler)ine > ait olup, T?B?TAK MAM bu e-posta i?eri?indeki bilgilerin > kullan?lmas? nedeniyle hi? kimseye kar?? sorumlu tutulamaz Mesaj?n > yetkili al?c?s? veya al?c?s?na iletmekten sorumlu ki?i de?ilseniz, > mesaj i?eri?ini ya da eklerini kullanmay?n?z, kopyalamay?n?z, > yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? g?nderen > ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n ve > bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in > korunmas? konusunda garanti vermemekte olup, e-posta i?eri?ine > yetkisiz olarak yap?lan m?dahale, vir?s i?ermesi ve/veya bilgisayar > sisteminize verebilece?i herhangi bir zarardan da sorumlu de?ildir. > > This e-mail message, including any attachments, is intended only for > the use of the individual or entity to whom it is addressed and may > contain confidential, private information as well as the exemption > from disclosure. All ideas and opinions in this message and attached > files can only belong to the addressee(s) and TUBITAK MRC shall > have no liability to any person with regard to the use of the > information contained in this message If you are not the intended > addressee(s) or responsible person to inform the addressee(s), you > are hereby notified that; any use, dissemination, distribution, or > copying of this message and attached files is strictly prohibited. > Delete the message and notify the sender immediately. TUBITAK MRC > do not warrant for the accuracy, completeness of the contents of > this email and/or the preservation of confidentiality and shall not > be liable for the unauthorized changes made to this message, > viruses and/or any damages caused in anyway to your computer system > ---------------------------------------------------------------- This message was sent using IMP, the Internet Messaging Program. From vickypu05 at gmail.com Sat Jun 4 01:48:38 2011 From: vickypu05 at gmail.com (vikas kumar) Date: Sat, 4 Jun 2011 14:18:38 +0530 Subject: [SAC-HELP] sac problem Message-ID: Sir, I rececived two mail from your side, after registering for SAC software, in first link i get sac-101.4.tar.gz(11.3 MB) and in second one i get sac-101.4-linux_x86_32.tar.gz( 7.3 MB). I have 32 bit configure computer. when i install the package sac-101.4.tar.gz it install but after going to the all procedure describe by you in readme it won,t run.But when i install sac-101.4-linux_x86_32.tar.gz it install and run.please tell me why this happen ? Is both these package is necessary to install? and if yes then how to install first one so that it run successfully?what is the difference in these packages why one installed and other not? With Regards -- Vikas Kumar Ministry of Earth Sciences Govt. of India New Delhi -------------- next part -------------- An HTML attachment was scrubbed... URL: From mplasencia at ogs.trieste.it Sat Jun 4 03:49:48 2011 From: mplasencia at ogs.trieste.it (Milton P. Plasencia Linares) Date: Sat, 04 Jun 2011 12:49:48 +0200 Subject: [SAC-HELP] sac problem In-Reply-To: References: Message-ID: <20110604124948.14782q5x7df9rsgc@webmail.ogs.trieste.it> Hi Vikas, The sac-101.4.tar.gz i understand that is the source software, so before that it can running you must to compile for your platform. Instead the sac-101.4-linux_x86_32.tar.gz is the binary distribution, ready (compiled) for running in OS Linux 32 bits PC, So, not is necessary "install" the sac-101.4.tar.gz. Cheers, Milton ********************************** Milton P. PLASENCIA LINARES Dipartimento Centro di Ricerche Sismologiche Istituto Nazionale di Oceanografia e di Geofisica Sperimentale - OGS Borgo Grotta Gigante 42/C (34010) Sgonico - TRIESTE - ITALIA Tel: +39-040-2140136 Fax: +39-040-327307 E-mail: mplasencia at ogs.trieste.it ASAIN (Antarctic Seismographic Argentinean Italian Network) ********************************* Quoting "vikas kumar" : > Sir, > I rececived two mail from your side, after registering for SAC software, > in first link i get sac-101.4.tar.gz(11.3 MB) and in second one i get > sac-101.4-linux_x86_32.tar.gz( > 7.3 MB). I have 32 bit configure computer. > when i install the package sac-101.4.tar.gz it install but after going to > the all procedure describe by you in readme it won,t run.But when i install > sac-101.4-linux_x86_32.tar.gz it install and run.please tell me why this > happen ? Is both these package is necessary to install? and if yes then how > to install first one so that it run successfully?what is the difference in > these packages why one installed and other not? > With Regards > -- > Vikas Kumar > Ministry of Earth Sciences > Govt. of India > New Delhi > ---------------------------------------------------------------- This message was sent using IMP, the Internet Messaging Program. From Mehmet.Ergin at mam.gov.tr Mon Jun 6 05:49:16 2011 From: Mehmet.Ergin at mam.gov.tr (Mehmet Ergin) Date: Mon, 6 Jun 2011 15:49:16 +0300 Subject: [SAC-HELP] cutting sac files on time In-Reply-To: <20110604073153.10566cc9zbdg770p@webmail.ogs.trieste.it> References: <9E88105FE4AC8C47BD6D00EB9831482F1F5B159C71@posta.mam.gov.tr> <20110604073153.10566cc9zbdg770p@webmail.ogs.trieste.it> Message-ID: <9E88105FE4AC8C47BD6D00EB9831482F1F5B159F08@posta.mam.gov.tr> Thanx for the try to help me, I know how we can use cut option. But I want to cut only time event by give time and duration. For example cut from 17:22:43.5 (hour:min:crc) to 100 seconds Hope you understand. Thanks very much. ---------------- Mehmet ERG?N Assoc.Prof. Chief Senior Scientist D:\poster ?ablonu\AcikTonluZemin.gif T?B?TAK Marmara Research Center Earth Sciences Institute P.O. Box 21, 41470 Gebze Kocaeli TURKEY T +90 262 677 2864 F +90 262 641 23 09 Mehmet.ergin at mam.gov.tr -----Original Message----- From: Milton P. Plasencia Linares [mailto:mplasencia at ogs.trieste.it] Sent: Saturday, June 04, 2011 8:32 AM To: Mehmet Ergin Cc: sac-help at iris.washington.edu Subject: Re: [SAC-HELP] cutting sac files on time Hi Mehmet, You must to use the cut command, using in this way: sac> cut t0 t1 sac> read file sac> plot sac> synchronize sac> plot In the second plot you see the time windows of cut, the "exact" time depend of your sampling rate, in other words, if you have 100 s/s you cant cut for example to=0.00 to t1=10.00, remember that the independent variable is t in seconds, so your cut resolution is 1/100 of second. Try cut 0.01 10.00 and cut 0.02 10.00, small values no works. HTH, Milton ********************************** Milton P. PLASENCIA LINARES Dipartimento Centro di Ricerche Sismologiche Istituto Nazionale di Oceanografia e di Geofisica Sperimentale - OGS Borgo Grotta Gigante 42/C (34010) Sgonico - TRIESTE - ITALIA Tel: +39-040-2140136 Fax: +39-040-327307 E-mail: mplasencia at ogs.trieste.it ASAIN (Antarctic Seismographic Argentinean Italian Network) ********************************* Quoting "Mehmet Ergin" : > Sent: Wednesday, June 01, 2011 11:17 AM > To: 'sac-help at iris.washington.edu' > Subject: cutting sac files on time > > Hi, > I just want to cut sac files only by giving exact time. I use to > sign to put T0 and then cut from T0 but always have problems to see > exact peak to cut, so I just want to give exact time to cut without > putting T0 . is it possible to cut files only by giving exact times. > thanx > > - > > ________________________________ > Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya > da kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi > gizlilik y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki > dosyalarda bulunan t?m fikir ve g?r??ler sadece adres sahip(ler)ine > ait olup, T?B?TAK MAM bu e-posta i?eri?indeki bilgilerin > kullan?lmas? nedeniyle hi? kimseye kar?? sorumlu tutulamaz Mesaj?n > yetkili al?c?s? veya al?c?s?na iletmekten sorumlu ki?i de?ilseniz, > mesaj i?eri?ini ya da eklerini kullanmay?n?z, kopyalamay?n?z, > yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? g?nderen > ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n ve > bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in > korunmas? konusunda garanti vermemekte olup, e-posta i?eri?ine > yetkisiz olarak yap?lan m?dahale, vir?s i?ermesi ve/veya bilgisayar > sisteminize verebilece?i herhangi bir zarardan da sorumlu de?ildir. > > This e-mail message, including any attachments, is intended only for > the use of the individual or entity to whom it is addressed and may > contain confidential, private information as well as the exemption > from disclosure. All ideas and opinions in this message and attached > files can only belong to the addressee(s) and TUBITAK MRC shall > have no liability to any person with regard to the use of the > information contained in this message If you are not the intended > addressee(s) or responsible person to inform the addressee(s), you > are hereby notified that; any use, dissemination, distribution, or > copying of this message and attached files is strictly prohibited. > Delete the message and notify the sender immediately. TUBITAK MRC > do not warrant for the accuracy, completeness of the contents of > this email and/or the preservation of confidentiality and shall not > be liable for the unauthorized changes made to this message, > viruses and/or any damages caused in anyway to your computer system > ---------------------------------------------------------------- This message was sent using IMP, the Internet Messaging Program. Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya da kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi gizlilik y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki dosyalarda bulunan t?m fikir ve g?r??ler sadece adres sahip(ler)ine ait olup, T?B?TAK MAM bu e-posta i?eri?indeki bilgilerin kullan?lmas? nedeniyle hi? kimseye kar?? sorumlu tutulamaz Mesaj?n yetkili al?c?s? veya al?c?s?na iletmekten sorumlu ki?i de?ilseniz, mesaj i?eri?ini ya da eklerini kullanmay?n?z, kopyalamay?n?z, yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? g?nderen ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n ve bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in korunmas? konusunda garanti vermemekte olup, e-posta i?eri?ine yetkisiz olarak yap?lan m?dahale, vir?s i?ermesi ve/veya bilgisayar sisteminize verebilece?i herhangi bir zarardan da sorumlu de?ildir. This e-mail message, including any attachments, is intended only for the use of the individual or entity to whom it is addressed and may contain confidential, private information as well as the exemption from disclosure. All ideas and opinions in this message and attached files can only belong to the addressee(s) and TUBITAK MRC shall have no liability to any person with regard to the use of the information contained in this message If you are not the intended addressee(s) or responsible person to inform the addressee(s), you are hereby notified that; any use, dissemination, distribution, or copying of this message and attached files is strictly prohibited. Delete the message and notify the sender immediately. TUBITAK MRC do not warrant for the accuracy, completeness of the contents of this email and/or the preservation of confidentiality and shall not be liable for the unauthorized changes made to this message, viruses and/or any damages caused in anyway to your computer system From mplasencia at ogs.trieste.it Mon Jun 6 08:20:22 2011 From: mplasencia at ogs.trieste.it (mplasencia at ogs.trieste.it) Date: Mon, 06 Jun 2011 17:20:22 +0200 Subject: [SAC-HELP] cutting sac files on time In-Reply-To: <9E88105FE4AC8C47BD6D00EB9831482F1F5B159F08@posta.mam.gov.tr> References: <9E88105FE4AC8C47BD6D00EB9831482F1F5B159C71@posta.mam.gov.tr> <20110604073153.10566cc9zbdg770p@webmail.ogs.trieste.it> <9E88105FE4AC8C47BD6D00EB9831482F1F5B159F08@posta.mam.gov.tr> Message-ID: <20110606172022.17072wiafqj8dbna@webmail.ogs.trieste.it> Hi Mehmet, If i understand your question correctly, you must to define a "marker" or reference, for example if your time 17:22:43.5 is the Origin time, you define the O variable in the sac header file prior the use of the cut command, after call the cut command, If you time 17.. is the start time of file use B, see the cut help. You can give data points using the N reference. HTH, Cheers, Milton Quoting "Mehmet Ergin" : > Thanx for the try to help me, I know how we can use cut option. > But I want to cut only time event by give time and duration. For > example cut from 17:22:43.5 (hour:min:crc) to 100 seconds > > Hope you understand. > Thanks very much. > > ---------------- > Mehmet ERG?N Assoc.Prof. > Chief Senior Scientist > > D:\poster ?ablonu\AcikTonluZemin.gif > T?B?TAK Marmara Research Center > Earth Sciences Institute > P.O. Box 21, 41470 Gebze Kocaeli TURKEY > T +90 262 677 2864 > F +90 262 641 23 09 > Mehmet.ergin at mam.gov.tr > > -----Original Message----- > From: Milton P. Plasencia Linares [mailto:mplasencia at ogs.trieste.it] > Sent: Saturday, June 04, 2011 8:32 AM > To: Mehmet Ergin > Cc: sac-help at iris.washington.edu > Subject: Re: [SAC-HELP] cutting sac files on time > > Hi Mehmet, > > You must to use the cut command, using in this way: > > sac> cut t0 t1 > sac> read file > sac> plot > sac> synchronize > sac> plot > > In the second plot you see the time windows of cut, the "exact" time > depend of your sampling rate, in other words, if you have 100 s/s > you cant cut for example to=0.00 to t1=10.00, remember that the independent > variable is t in seconds, so your cut resolution is 1/100 of second. > Try cut 0.01 10.00 and cut 0.02 10.00, small values no works. > > HTH, > > Milton > > > ********************************** > Milton P. PLASENCIA LINARES > > Dipartimento Centro di Ricerche Sismologiche > Istituto Nazionale di Oceanografia e di Geofisica Sperimentale - OGS > > Borgo Grotta Gigante 42/C > (34010) Sgonico - TRIESTE - ITALIA > Tel: +39-040-2140136 > Fax: +39-040-327307 > > E-mail: mplasencia at ogs.trieste.it > > ASAIN (Antarctic Seismographic Argentinean Italian Network) > ********************************* > > > Quoting "Mehmet Ergin" : > >> Sent: Wednesday, June 01, 2011 11:17 AM >> To: 'sac-help at iris.washington.edu' >> Subject: cutting sac files on time >> >> Hi, >> I just want to cut sac files only by giving exact time. I use to >> sign to put T0 and then cut from T0 but always have problems to see >> exact peak to cut, so I just want to give exact time to cut without >> putting T0 . is it possible to cut files only by giving exact times. >> thanx >> >> - >> >> ________________________________ >> Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya >> da kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi >> gizlilik y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki >> dosyalarda bulunan t?m fikir ve g?r??ler sadece adres sahip(ler)ine >> ait olup, T?B?TAK MAM bu e-posta i?eri?indeki bilgilerin >> kullan?lmas? nedeniyle hi? kimseye kar?? sorumlu tutulamaz Mesaj?n >> yetkili al?c?s? veya al?c?s?na iletmekten sorumlu ki?i de?ilseniz, >> mesaj i?eri?ini ya da eklerini kullanmay?n?z, kopyalamay?n?z, >> yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? g?nderen >> ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n ve >> bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in >> korunmas? konusunda garanti vermemekte olup, e-posta i?eri?ine >> yetkisiz olarak yap?lan m?dahale, vir?s i?ermesi ve/veya bilgisayar >> sisteminize verebilece?i herhangi bir zarardan da sorumlu de?ildir. >> >> This e-mail message, including any attachments, is intended only for >> the use of the individual or entity to whom it is addressed and may >> contain confidential, private information as well as the exemption >> from disclosure. All ideas and opinions in this message and attached >> files can only belong to the addressee(s) and TUBITAK MRC shall >> have no liability to any person with regard to the use of the >> information contained in this message If you are not the intended >> addressee(s) or responsible person to inform the addressee(s), you >> are hereby notified that; any use, dissemination, distribution, or >> copying of this message and attached files is strictly prohibited. >> Delete the message and notify the sender immediately. TUBITAK MRC >> do not warrant for the accuracy, completeness of the contents of >> this email and/or the preservation of confidentiality and shall not >> be liable for the unauthorized changes made to this message, >> viruses and/or any damages caused in anyway to your computer system >> > > > > ---------------------------------------------------------------- > This message was sent using IMP, the Internet Messaging Program. > > > Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya > da kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi > gizlilik y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki > dosyalarda bulunan t?m fikir ve g?r??ler sadece adres sahip(ler)ine > ait olup, T?B?TAK MAM bu e-posta i?eri?indeki bilgilerin > kullan?lmas? nedeniyle hi? kimseye kar?? sorumlu tutulamaz Mesaj?n > yetkili al?c?s? veya al?c?s?na iletmekten sorumlu ki?i de?ilseniz, > mesaj i?eri?ini ya da eklerini kullanmay?n?z, kopyalamay?n?z, > yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? g?nderen > ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n ve > bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in > korunmas? konusunda garanti vermemekte olup, e-posta i?eri?ine > yetkisiz olarak yap?lan m?dahale, vir?s i?ermesi ve/veya bilgisayar > sisteminize verebilece?i herhangi bir zarardan da sorumlu de?ildir. > > This e-mail message, including any attachments, is intended only for > the use of the individual or entity to whom it is addressed and may > contain confidential, private information as well as the exemption > from disclosure. All ideas and opinions in this message and attached > files can only belong to the addressee(s) and TUBITAK MRC shall > have no liability to any person with regard to the use of the > information contained in this message If you are not the intended > addressee(s) or responsible person to inform the addressee(s), you > are hereby notified that; any use, dissemination, distribution, or > copying of this message and attached files is strictly prohibited. > Delete the message and notify the sender immediately. TUBITAK MRC do > not warrant for the accuracy, completeness of the contents of this > email and/or the preservation of confidentiality and shall not be > liable for the unauthorized changes made to this message, viruses > and/or any damages caused in anyway to your computer system > ---------------------------------------------------------------- This message was sent using IMP, the Internet Messaging Program. From u2injesus at gmail.com Thu Jun 9 00:32:42 2011 From: u2injesus at gmail.com (jenni wang) Date: Thu, 9 Jun 2011 09:32:42 +0200 Subject: [SAC-HELP] ask: transfer function Message-ID: All sac users: I am a beginner here, so I would like to ask some questions, I hope some advanced user of sac can help me with my doubts about transfer command. 1. I have a seismogram waveform which is velocity record from velocity transducer. I have the response instrument read with rdseed and the RESP.* is the velocity response, but the pole zero is displacement response. My question: When I apply trans from polezero ..., using that polezero obtained from rdseed, do I get the velocity ground motion (m/s or nm/s, etc. ) or do I get displacement ground motion? 2. After the deconvolution with the transfer command, can I do the convolution to apply another instrument response of the instrument types that are not in the list in sac reference manual? If yes, how can I do it? If not, would anyone please tell me the source where I can get the frequency response and polezero of the instrument types in the sac manual since I am trying to compare records that could be obtained from different instruments with different response. Thanks, J. -------------- next part -------------- An HTML attachment was scrubbed... URL: From Onur.Tan at mam.gov.tr Thu Jun 9 01:42:23 2011 From: Onur.Tan at mam.gov.tr (Onur Tan) Date: Thu, 9 Jun 2011 11:42:23 +0300 Subject: [SAC-HELP] ask: transfer function In-Reply-To: Message-ID: Hello 1. I have a seismogram waveform which is velocity record from velocity transducer. I have the response instrument read with rdseed and the RESP.* is the velocity response, but the pole zero is displacement response. My question: When I apply trans from polezero ..., using that polezero obtained from rdseed, do I get the velocity ground motion (m/s or nm/s, etc. ) or do I get displacement ground motion? your input velocity PZ file must have an additional ZERO for SAC. SAC integrates the data with that ZERO. if you say ?to none? your output will be disp. (m) ; if you say ?to vel? you will get velocity (m/s) 2. After the deconvolution with the transfer command, can I do the convolution to apply another instrument response of the instrument types that are not in the list in sac reference manual? If yes, how can I do it? If not, would anyone please tell me the source where I can get the frequency response and polezero of the instrument types in the sac manual since I am trying to compare records that could be obtained from different instruments with different response. you need a PZ file of output instruments. you can say ?from polezero to new-polezero?. best regards o. Dr. Onur TAN ---------------------------------------------- 40.7866N 29.4500E --------- T?B?TAK Marmara Ara?t?rma Merkezi, Yer ve Deniz Bilimleri Enstit?s? TUBITAK Marmara Research Center, Earth and Marine Sciences Institute Gebze - Kocaeli - TURKEY ________________________________ Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya da kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi gizlilik y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki dosyalarda bulunan t?m fikir ve g?r??ler sadece adres sahip(ler)ine ait olup, T?B?TAK MAM bu e-posta i?eri?indeki bilgilerin kullan?lmas? nedeniyle hi? kimseye kar?? sorumlu tutulamaz Mesaj?n yetkili al?c?s? veya al?c?s?na iletmekten sorumlu ki?i de?ilseniz, mesaj i?eri?ini ya da eklerini kullanmay?n?z, kopyalamay?n?z, yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? g?nderen ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n ve bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in korunmas? konusunda garanti vermemekte olup, e-posta i?eri?ine yetkisiz olarak yap?lan m?dahale, vir?s i?ermesi ve/veya bilgisayar sisteminize verebilece?i herhangi bir zarardan da sorumlu de?ildir. This e-mail message, including any attachments, is intended only for the use of the individual or entity to whom it is addressed and may contain confidential, private information as well as the exemption from disclosure. All ideas and opinions in this message and attached files can only belong to the addressee(s) and TUBITAK MRC shall have no liability to any person with regard to the use of the information contained in this message If you are not the intended addressee(s) or responsible person to inform the addressee(s), you are hereby notified that; any use, dissemination, distribution, or copying of this message and attached files is strictly prohibited. Delete the message and notify the sender immediately. TUBITAK MRC do not warrant for the accuracy, completeness of the contents of this email and/or the preservation of confidentiality and shall not be liable for the unauthorized changes made to this message, viruses and/or any damages caused in anyway to your computer system From u2injesus at gmail.com Thu Jun 9 02:12:44 2011 From: u2injesus at gmail.com (jenni wang) Date: Thu, 9 Jun 2011 11:12:44 +0200 Subject: [SAC-HELP] ask: transfer function In-Reply-To: References: Message-ID: All sac user: @Thank you for the explanation, Dr. Onur. But I still have problem regarding my second question. I have my polezero file, but when I did as you suggest: from polezero to *.pz (e.g.polezero file obtained from http://www.passcal.nmt.edu/content/instrumentation/sensors/sensor-comparison-chart), I got the error message: ERROR interpreting command: trans from polezero s' to ' Unkown instrument type: Could anyone please help me to point out the mistake I made and tell me the right command to apply to get the convolution done? Thanks, J. On Thu, Jun 9, 2011 at 10:42 AM, Onur Tan wrote: > Hello > > 1. I have a seismogram waveform which is velocity record from velocity > transducer. I have the response instrument read with rdseed and the RESP.* > is the velocity response, but the pole zero is displacement response. My > question: When I apply trans from polezero ..., using that polezero obtained > from rdseed, do I get the velocity ground motion (m/s or nm/s, etc. ) or do > I get displacement ground motion? > > your input velocity PZ file must have an additional ZERO for SAC. SAC > integrates the data with that ZERO. if you say "to none" your output will be > disp. (m) ; if you say "to vel" you will get velocity (m/s) > > 2. After the deconvolution with the transfer command, can I do the > convolution to apply another instrument response of the instrument types > that are not in the list in sac reference manual? If yes, how can I do it? > If not, would anyone please tell me the source where I can get the frequency > response and polezero of the instrument types in the sac manual since I am > trying to compare records that could be obtained from different instruments > with different response. > > you need a PZ file of output instruments. you can say "from polezero > to new-polezero". > > best regards > o. > > > > Dr. Onur TAN > ---------------------------------------------- 40.7866N 29.4500E > --------- > T?B?TAK Marmara Ara?t?rma Merkezi, Yer ve Deniz Bilimleri Enstit?s? > TUBITAK Marmara Research Center, Earth and Marine Sciences Institute > Gebze - Kocaeli - TURKEY > > ________________________________ > Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya da > kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi gizlilik > y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki dosyalarda bulunan > t?m fikir ve g?r??ler sadece adres sahip(ler)ine ait olup, T?B?TAK MAM bu > e-posta i?eri?indeki bilgilerin kullan?lmas? nedeniyle hi? kimseye kar?? > sorumlu tutulamaz Mesaj?n yetkili al?c?s? veya al?c?s?na iletmekten sorumlu > ki?i de?ilseniz, mesaj i?eri?ini ya da eklerini kullanmay?n?z, > kopyalamay?n?z, yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? > g?nderen ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n > ve bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in korunmas? > konusunda garanti vermemekte olup, e-posta i?eri?ine yetkisiz olarak yap?lan > m?dahale, vir?s i?ermesi ve/veya bilgisayar sisteminize verebilece?i > herhangi bir zarardan da sorumlu de?ildir. > > This e-mail message, including any attachments, is intended only for the > use of the individual or entity to whom it is addressed and may contain > confidential, private information as well as the exemption from disclosure. > All ideas and opinions in this message and attached files can only belong to > the addressee(s) and TUBITAK MRC shall have no liability to any person with > regard to the use of the information contained in this message If you are > not the intended addressee(s) or responsible person to inform the > addressee(s), you are hereby notified that; any use, dissemination, > distribution, or copying of this message and attached files is strictly > prohibited. Delete the message and notify the sender immediately. TUBITAK > MRC do not warrant for the accuracy, completeness of the contents of this > email and/or the preservation of confidentiality and shall not be liable for > the unauthorized changes made to this message, viruses and/or any damages > caused in anyway to your computer system > > _______________________________________________ > sac-help mailing list > sac-help at iris.washington.edu > http://www.iris.washington.edu/mailman/listinfo/sac-help > -------------- next part -------------- An HTML attachment was scrubbed... URL: From snoke at vt.edu Thu Jun 9 03:44:11 2011 From: snoke at vt.edu (Arthur Snoke) Date: Thu, 9 Jun 2011 06:44:11 -0400 (EDT) Subject: [SAC-HELP] ask: transfer function In-Reply-To: References: Message-ID: for your first question, you might consider using the evalresp option in transfer. Also, polezero files written using recent versions of rdseed have comment lines that give details about things like the input and output units. (Do note that rdseed uses m and SAC header says nm. See the transfer help message for a discussion.) For your second question, it would help if you copied/pasted the command sequence into an e-mail message. On Thu, 9 Jun 2011, jenni wang wrote: > All sac user: > > @Thank you for the explanation, Dr. Onur. > But I still have problem regarding my second question. I have my polezero > file, but when I did as you suggest: from polezero to *.pz (e.g.polezero > file obtained fromhttp://www.passcal.nmt.edu/content/instrumentation/sensors/sensor-compariso > n-chart), I got the error message: > ERROR interpreting command: trans from polezero s'? to ' > Unkown instrument type: > > Could anyone please help me to point out the mistake I made and tell me the > right command to apply to get the convolution done? > > Thanks, > J. > > On Thu, Jun 9, 2011 at 10:42 AM, Onur Tan wrote: > Hello > > 1. I have a seismogram waveform which is velocity record from > velocity transducer. I have the response instrument read with > rdseed and the RESP.* is the velocity response, but the pole > zero is displacement response. My question: When I apply trans > from polezero ..., using that polezero obtained from rdseed, do > I get the velocity ground motion (m/s or nm/s, etc. ) or do I > get displacement ground motion? > > your input velocity PZ file must have an additional ZERO for SAC. SAC > integrates the data with that ZERO. if you say ?to none? your output > will be disp. (m) ; if you say ?to vel? you will get velocity (m/s) > > 2. After the deconvolution with the transfer command, can I do the > convolution to apply another instrument response of the instrument > types that are not in the list in sac reference manual? If yes, how > can I do it? If not, would anyone please tell me the source where I > can get the frequency response and polezero of the instrument types in > the sac manual since I am trying to compare ?records that could be > obtained from different instruments with different response. > > ? ?you need a PZ file of output instruments. you can say ??from > polezero to new-polezero?. > > best regards > o. From u2injesus at gmail.com Fri Jun 10 03:50:56 2011 From: u2injesus at gmail.com (jenni wang) Date: Fri, 10 Jun 2011 12:50:56 +0200 Subject: [SAC-HELP] ask: transfer function In-Reply-To: References: Message-ID: @Thank you for the info, Arthur. Is there any difference by applying polezero or evalresp? I got error with this command: trans from polezero s %pzfile to polezero s 1s.pz Could anyone please help to find out the mistake I make? Thanks, J. On Thu, Jun 9, 2011 at 12:44 PM, Arthur Snoke wrote: > for your first question, you might consider using the evalresp option in > transfer. Also, polezero files written using recent versions of rdseed have > comment lines that give details about things like the input and output > units. (Do note that rdseed uses m and SAC header says nm. See the transfer > help message for a discussion.) > > For your second question, it would help if you copied/pasted the command > sequence into an e-mail message. > > > On Thu, 9 Jun 2011, jenni wang wrote: > > All sac user: >> >> @Thank you for the explanation, Dr. Onur. >> But I still have problem regarding my second question. I have my polezero >> file, but when I did as you suggest: from polezero to *.pz (e.g.polezero >> file obtained fromhttp:// >> www.passcal.nmt.edu/content/instrumentation/sensors/sensor-compariso >> >> n-chart), I got the error message: >> ERROR interpreting command: trans from polezero s' to ' >> Unkown instrument type: >> >> Could anyone please help me to point out the mistake I made and tell me >> the >> right command to apply to get the convolution done? >> >> Thanks, >> J. >> >> On Thu, Jun 9, 2011 at 10:42 AM, Onur Tan wrote: >> Hello >> >> 1. I have a seismogram waveform which is velocity record from >> velocity transducer. I have the response instrument read with >> rdseed and the RESP.* is the velocity response, but the pole >> zero is displacement response. My question: When I apply trans >> from polezero ..., using that polezero obtained from rdseed, do >> I get the velocity ground motion (m/s or nm/s, etc. ) or do I >> get displacement ground motion? >> >> your input velocity PZ file must have an additional ZERO for SAC. SAC >> integrates the data with that ZERO. if you say ?to none? your output >> will be disp. (m) ; if you say ?to vel? you will get velocity (m/s) >> >> 2. After the deconvolution with the transfer command, can I do the >> convolution to apply another instrument response of the instrument >> types that are not in the list in sac reference manual? If yes, how >> can I do it? If not, would anyone please tell me the source where I >> can get the frequency response and polezero of the instrument types in >> the sac manual since I am trying to compare records that could be >> obtained from different instruments with different response. >> >> you need a PZ file of output instruments. you can say ?from >> polezero to new-polezero?. >> >> best regards >> o. >> > -------------- next part -------------- An HTML attachment was scrubbed... URL: From mplasencia at ogs.trieste.it Sat Jun 11 01:21:21 2011 From: mplasencia at ogs.trieste.it (Milton P. Plasencia Linares) Date: Sat, 11 Jun 2011 10:21:21 +0200 Subject: [SAC-HELP] ask: transfer function In-Reply-To: References: Message-ID: <20110611102121.16926cjapv1vg96p@webmail.ogs.trieste.it> Hi Jenni, yes, there is different, evalresp use the Response file that is the "complete" response of the system, instead the polezero only include the poles and zeros of sensor and constant can include the amplitude factor of the digitizer. For debugging the transfer command you can start using the half of command, sac> trans from polezero s polezero_file to none and after add the second part, i suspect of use the second part, verify the path of the 1s.pz file, HTH, Milton ********************************** Milton P. PLASENCIA LINARES Dipartimento Centro di Ricerche Sismologiche Istituto Nazionale di Oceanografia e di Geofisica Sperimentale - OGS Borgo Grotta Gigante 42/C (34010) Sgonico - TRIESTE - ITALIA Tel: +39-040-2140136 Fax: +39-040-327307 E-mail: mplasencia at ogs.trieste.it ASAIN (Antarctic Seismographic Argentinean Italian Network) ********************************* Quoting "jenni wang" : > @Thank you for the info, Arthur. Is there any difference by applying > polezero or evalresp? > > I got error with this command: > trans from polezero s %pzfile to polezero s 1s.pz > > Could anyone please help to find out the mistake I make? > > Thanks, > J. > > > On Thu, Jun 9, 2011 at 12:44 PM, Arthur Snoke wrote: > >> for your first question, you might consider using the evalresp option in >> transfer. Also, polezero files written using recent versions of rdseed have >> comment lines that give details about things like the input and output >> units. (Do note that rdseed uses m and SAC header says nm. See the transfer >> help message for a discussion.) >> >> For your second question, it would help if you copied/pasted the command >> sequence into an e-mail message. >> >> >> On Thu, 9 Jun 2011, jenni wang wrote: >> >> All sac user: >>> >>> @Thank you for the explanation, Dr. Onur. >>> But I still have problem regarding my second question. I have my polezero >>> file, but when I did as you suggest: from polezero to *.pz (e.g.polezero >>> file obtained fromhttp:// >>> www.passcal.nmt.edu/content/instrumentation/sensors/sensor-compariso >>> >>> n-chart), I got the error message: >>> ERROR interpreting command: trans from polezero s' to ' >>> Unkown instrument type: >>> >>> Could anyone please help me to point out the mistake I made and tell me >>> the >>> right command to apply to get the convolution done? >>> >>> Thanks, >>> J. >>> >>> On Thu, Jun 9, 2011 at 10:42 AM, Onur Tan wrote: >>> Hello >>> >>> 1. I have a seismogram waveform which is velocity record from >>> velocity transducer. I have the response instrument read with >>> rdseed and the RESP.* is the velocity response, but the pole >>> zero is displacement response. My question: When I apply trans >>> from polezero ..., using that polezero obtained from rdseed, do >>> I get the velocity ground motion (m/s or nm/s, etc. ) or do I >>> get displacement ground motion? >>> >>> your input velocity PZ file must have an additional ZERO for SAC. SAC >>> integrates the data with that ZERO. if you say ?to none? your output >>> will be disp. (m) ; if you say ?to vel? you will get velocity (m/s) >>> >>> 2. After the deconvolution with the transfer command, can I do the >>> convolution to apply another instrument response of the instrument >>> types that are not in the list in sac reference manual? If yes, how >>> can I do it? If not, would anyone please tell me the source where I >>> can get the frequency response and polezero of the instrument types in >>> the sac manual since I am trying to compare records that could be >>> obtained from different instruments with different response. >>> >>> you need a PZ file of output instruments. you can say ?from >>> polezero to new-polezero?. >>> >>> best regards >>> o. >>> >> > ---------------------------------------------------------------- This message was sent using IMP, the Internet Messaging Program. From kawsarl at yahoo.co.in Mon Jun 20 03:27:16 2011 From: kawsarl at yahoo.co.in (Kawsar Laskar) Date: Mon, 20 Jun 2011 10:27:16 +0000 (UTC) Subject: [SAC-HELP] Invitation to connect on LinkedIn Message-ID: <1926623664.2882696.1308565636134.JavaMail.app@ela4-bed78.prod> LinkedIn ------------ I'd like to add you to my professional network on LinkedIn. - Kawsar Kawsar Laskar Engineer at Consulting Consulting Engineering Services (India) Pvt. Ltd. New Delhi Area, India Confirm that you know Kawsar Laskar https://www.linkedin.com/e/-9ou29g-gp5a6yw1-2o/isd/3271279359/PMc4wDvC/ -- (c) 2011, LinkedIn Corporation -------------- next part -------------- An HTML attachment was scrubbed... URL: From kawsarl at yahoo.co.in Mon Jun 20 03:27:46 2011 From: kawsarl at yahoo.co.in (Kawsar Laskar) Date: Mon, 20 Jun 2011 10:27:46 +0000 (UTC) Subject: [SAC-HELP] Invitation to connect on LinkedIn Message-ID: <1174341428.2879984.1308565666668.JavaMail.app@ela4-bed81.prod> LinkedIn ------------ I'd like to add you to my professional network on LinkedIn. - Kawsar Kawsar Laskar Engineer at Consulting Consulting Engineering Services (India) Pvt. Ltd. New Delhi Area, India Confirm that you know Kawsar Laskar https://www.linkedin.com/e/-9ou29g-gp5a7mg9-55/isd/3271279359/PMc4wDvC/ -- (c) 2011, LinkedIn Corporation -------------- next part -------------- An HTML attachment was scrubbed... URL: From Onur.Tan at mam.gov.tr Mon Jun 20 04:05:50 2011 From: Onur.Tan at mam.gov.tr (Onur Tan) Date: Mon, 20 Jun 2011 14:05:50 +0300 Subject: [SAC-HELP] moving RMS Message-ID: Hi, I want to calculate moving RMS values on a data file. i.e. I have one day time series, and want to calculate RMS value within 101 points window at each sample. I think that the rms command has not a moving window. is there a tool in SAC? thanks. onur Dr. Onur TAN ---------------------------------------------- 40.7866N 29.4500E --------- T?B?TAK Marmara Ara?t?rma Merkezi, Yer ve Deniz Bilimleri Enstit?s? TUBITAK Marmara Research Center, Earth and Marine Sciences Institute Gebze - Kocaeli - TURKEY ________________________________ Bu e-posta mesaj? ve onunla iletilen t?m ekler g?nderildi?i ki?i ya da kuruma ?zel olup, gizli ve ?zel bilgiler i?erebilece?i gibi gizlilik y?k?ml?l??? de ta??yor olabilir. Bu mesajda ve ekindeki dosyalarda bulunan t?m fikir ve g?r??ler sadece adres sahip(ler)ine ait olup, T?B?TAK MAM bu e-posta i?eri?indeki bilgilerin kullan?lmas? nedeniyle hi? kimseye kar?? sorumlu tutulamaz Mesaj?n yetkili al?c?s? veya al?c?s?na iletmekten sorumlu ki?i de?ilseniz, mesaj i?eri?ini ya da eklerini kullanmay?n?z, kopyalamay?n?z, yaymay?n?z, ba?ka ki?ilere y?nlendirmeyiniz ve mesaj? g?nderen ki?iyi derhal uyararak bu mesaj? siliniz. Kurumumuz size, mesaj?n ve bilgilerinin de?i?ikli?e u?ramamas?, b?t?nl???n?n ve gizlili?in korunmas? konusunda garanti vermemekte olup, e-posta i?eri?ine yetkisiz olarak yap?lan m?dahale, vir?s i?ermesi ve/veya bilgisayar sisteminize verebilece?i herhangi bir zarardan da sorumlu de?ildir. This e-mail message, including any attachments, is intended only for the use of the individual or entity to whom it is addressed and may contain confidential, private information as well as the exemption from disclosure. All ideas and opinions in this message and attached files can only belong to the addressee(s) and TUBITAK MRC shall have no liability to any person with regard to the use of the information contained in this message If you are not the intended addressee(s) or responsible person to inform the addressee(s), you are hereby notified that; any use, dissemination, distribution, or copying of this message and attached files is strictly prohibited. Delete the message and notify the sender immediately. TUBITAK MRC do not warrant for the accuracy, completeness of the contents of this email and/or the preservation of confidentiality and shall not be liable for the unauthorized changes made to this message, viruses and/or any damages caused in anyway to your computer system From metin.kahraman at boun.edu.tr Wed Jun 22 17:55:00 2011 From: metin.kahraman at boun.edu.tr (Metin Kahraman) Date: Thu, 23 Jun 2011 03:55:00 +0300 Subject: [SAC-HELP] increase SAC Graphich window Message-ID: Dear SAC users, I am using SAC for my seismogram analysis. I prepared a SAC macro which help me see the wave forms and pick the arrival times. My question is when I read my data with read command in sac and plot them with ppk, a Graphic window is opened and I can see the wave forms but my computer screen is not so big so that I have difficulty to see exact time of arrival time. I am using my mouse to get larger of Graphical window. but the ne wave forms open small size. What I want to do is, I would like to get larger graphical window using sac commands in a macro. I tried 'window' command but it did not worked. it does not much effect to size of seismogram. Do you know how can increase size of opening graphical window after typing 'ppk' Best wishes Metin Kahraman From metin.kahraman at boun.edu.tr Thu Jun 23 04:52:11 2011 From: metin.kahraman at boun.edu.tr (Metin Kahraman) Date: Thu, 23 Jun 2011 14:52:11 +0300 Subject: [SAC-HELP] increase SAC Graphich window In-Reply-To: <4B8276CA-DBB6-40A9-A181-C376F290D08B@gmail.com> References: <4B8276CA-DBB6-40A9-A181-C376F290D08B@gmail.com> Message-ID: <4E0328EB.3000207@boun.edu.tr> Dear Zheng, Thank you for your fast reply, zoom is one of the option but it is not what I am looking for, Basically, Graphical window of SAC pop up in a default size, I want to enlarge this graphical window, I mean, I want larger pop up graphical window. One of the way doing this, change my computer screen for example using 23 inc screen, but I suppose pop up large graphical window will do the same effect without change my screen. All my best Metin Yingcai Zheng wrote: > Sac can zoom in. > You need use keyboard. > After 'ppk' > Move your cursor to say t=5 sec > And press 'x' from keyboard. > Then move the cursor to say t=10 and then press 'x'. Sac will magnify the portion of waveform between 5 and 10 secs. When u r down , press 'o'. > > On Jun 22, 2011, at 8:55 PM, Metin Kahraman wrote: > > >> Dear SAC users, >> >> I am using SAC for my seismogram analysis. I prepared a SAC macro which help me see the wave forms and pick the arrival times. >> >> My question is when I read my data with read command in sac and plot them with ppk, a Graphic window is opened and I can see the wave forms but my computer screen is not so big so that I have difficulty to see exact time of arrival time. I am using my mouse to get larger of Graphical window. but the ne wave forms open small size. What I want to do is, I would like to get larger graphical window using sac commands in a macro. >> >> I tried 'window' command but it did not worked. it does not much effect to size of seismogram. >> >> Do you know how can increase size of opening graphical window after typing 'ppk' >> >> Best wishes >> >> Metin Kahraman >> >> >> _______________________________________________ >> sac-help mailing list >> sac-help at iris.washington.edu >> http://www.iris.washington.edu/mailman/listinfo/sac-help >> > > -------------- next part -------------- An HTML attachment was scrubbed... URL: From rc202388 at ucla.edu Thu Jun 23 10:01:34 2011 From: rc202388 at ucla.edu (rc202388 at ucla.edu) Date: Thu, 23 Jun 2011 10:01:34 -0700 Subject: [SAC-HELP] Installing SAC in Linux Message-ID: <20110623100134.12832yk12dn0zxq8@mail.ucla.edu> Hello, I am trying to install SAC onto Linux. Does it work in the most recent version of Ubuntu or does it only work in CentOS 4.7? If it only works in CentOS, what binary does should I download? ( The mirror sites give 5 different binaries, bin1of5, bin2of5, bin3of5, ext. ) Thank you for your help. Raymond Chen From savage at uri.edu Thu Jun 23 10:45:32 2011 From: savage at uri.edu (Brian Savage) Date: Thu, 23 Jun 2011 13:45:32 -0400 Subject: [SAC-HELP] Installing SAC in Linux In-Reply-To: <20110623100134.12832yk12dn0zxq8@mail.ucla.edu> References: <20110623100134.12832yk12dn0zxq8@mail.ucla.edu> Message-ID: <9459C28D-15E7-4945-8887-11E6B4E60E15@uri.edu> Dear Raymond, SAC should be fine on the most recent version of Ubuntu. If the binary for Linux, either 32 or 64 bit, does not work you may need to compile it yourself. Brian Savage savage at uri.edu On Jun 23, 2011, at 1:01 PM, rc202388 at ucla.edu wrote: > Hello, > > I am trying to install SAC onto Linux. Does it work > in the most recent version of Ubuntu or does it only > work in CentOS 4.7? If it only works in CentOS, > what binary does should I download? ( The mirror > sites give 5 different binaries, bin1of5, bin2of5, > bin3of5, ext. ) > > Thank you for your help. > Raymond Chen > _______________________________________________ > sac-help mailing list > sac-help at iris.washington.edu > http://www.iris.washington.edu/mailman/listinfo/sac-help > From member at linkedin.com Sat Jun 25 00:47:30 2011 From: member at linkedin.com (Amarjeet Kumar via LinkedIn) Date: Sat, 25 Jun 2011 07:47:30 +0000 (UTC) Subject: [SAC-HELP] Invitation to connect on LinkedIn Message-ID: <1875158973.641868.1308988050173.JavaMail.app@ela4-bed78.prod> LinkedIn ------------ Amarjeet Kumar requested to add you as a connection on LinkedIn: ------------------------------------------ Sac Help, I'd like to add you to my professional network on LinkedIn. - Amarjeet Accept invitation from Amarjeet Kumar http://www.linkedin.com/e/-9ou29g-gpc9orne-j/ubIx8rFs5oSdYQa2oQHQ-lofPc2q7sw6cHvfFlhxuru/blk/I20106023_125/1BpC5vrmRLoRZcjkkZt5YCpnlOt3RApnhMpmdzgmhxrSNBszYRcz5vcP8Mdz0Nc399bP5TsktGm3sRbP8QdPgQcjgPcPcLrCBxbOYWrSlI/EML_comm_afe/ View invitation from Amarjeet Kumar http://www.linkedin.com/e/-9ou29g-gpc9orne-j/ubIx8rFs5oSdYQa2oQHQ-lofPc2q7sw6cHvfFlhxuru/blk/I20106023_125/3kOclYPcz0Sc34McAALqnpPbOYWrSlI/svi/ ------------------------------------------ Why might connecting with Amarjeet Kumar be a good idea? Have a question? Amarjeet Kumar's network will probably have an answer: You can use LinkedIn Answers to distribute your professional questions to Amarjeet Kumar and your extended network. You can get high-quality answers from experienced professionals. http://www.linkedin.com/e/-9ou29g-gpc9orne-j/ash/inv19_ayn/ -- (c) 2011, LinkedIn Corporation -------------- next part -------------- An HTML attachment was scrubbed... URL: From alireza.alinaghi at gmail.com Mon Jun 27 03:58:42 2011 From: alireza.alinaghi at gmail.com (Alireza Alinaghi) Date: Mon, 27 Jun 2011 12:58:42 +0200 Subject: [SAC-HELP] taup_setsac errors in setting theoretical arrival times of phases Message-ID: Dear Friends and Colleagues: In an attempt to put the theoretical arrival times in SAC headers, I have used a program contained in TAU_P package, called "taup_setsac". I called this program both within and without SAC environment but I always get the following error: SAC> taup_setsac -ph P -evdpkm -verbose GRA1.Z Exception in thread "main" java.lang.NullPointerException at edu.sc.seis.TauP.TauP_SetSac.parseCmdLineArgs(TauP_SetSac.java:353) at edu.sc.seis.TauP.TauP_SetSac.main(TauP_SetSac.java:382) Does anyone know what goes wrong? Or are there alternative ways to do the job? I have SAC 101.4 running on Fedora14 with Java SE build 1.6.0_25-b06. The other TAUP programs run without any error. Thank you in advance for your hints. Alireza -------------- next part -------------- An HTML attachment was scrubbed... URL: From snoke at vt.edu Mon Jun 27 05:37:04 2011 From: snoke at vt.edu (Arthur Snoke) Date: Mon, 27 Jun 2011 08:37:04 -0400 (EDT) Subject: [SAC-HELP] taup_setsac errors in setting theoretical arrival times of phases In-Reply-To: References: Message-ID: As noted in the traveltime help file that comes with version 101.4, traveltime in IRIS/SAC does not work. although not directly related to your quesiton, I would appreciate it if anyone has succeeded in getting something like the iaspei-tau program ttimes working in C. If so, please send me the source as I would like to fix at least that part of the sss/traveltime command. What you have done is very similar to what is suggested in the SAC help file escept you leave out the sc and the -1 in P-1. On my mac (OS 10.6) I reproduced the results in the help file with a line like yours: SAC> taup_setsac -evdpkm -ph P -verbose test.z test.z Using gcarc: 3.3574646 test.z searching for P P: P END 0 1 2 3 4 5 5 4 3 2 1 0 minRayParam=254.33137581441554 maxRayParam=1098.448275862069 minDistance=0.0 maxDistance=98.39983407057541 ----------------- test.z 5 arrivals found. test.z phase found P -> t0, travel time=64.63958 test.z phase found P -> t0, travel time=64.35809 test.z phase found P -> t0, travel time=60.571896 test.z phase found P -> t0, travel time=60.38368 test.z phase found P -> t0, travel time=53.694054 SAC> r test.z SAC> lh amarker t1marker FILE: test.z - 1 ------------ amarker = 10.47 t1marker = 10.494 (P) SAC> As you get the same error outside of SAC, it sounds like your immediate problem is with the taup on your system. On Mon, 27 Jun 2011, Alireza Alinaghi wrote: > Dear Friends and Colleagues: > > In an attempt to put the theoretical arrival times in SAC headers, I > have used a program contained in TAU_P package, called "taup_setsac". ?I > called this program both within and without SAC environment but I always > get the following error: > > SAC> taup_setsac -ph P -evdpkm -verbose GRA1.Z > Exception in thread "main" java.lang.NullPointerException > at edu.sc.seis.TauP.TauP_SetSac.parseCmdLineArgs(TauP_SetSac.java:353) > at edu.sc.seis.TauP.TauP_SetSac.main(TauP_SetSac.java:382) > > Does anyone know what goes wrong? Or are there alternative ways to do > the job? > > I have SAC 101.4 running on Fedora14 with Java SE ?build 1.6.0_25-b06. > The other TAUP programs run without any error. > > Thank you in advance for your hints. > > Alireza From crotwell at seis.sc.edu Mon Jun 27 07:55:47 2011 From: crotwell at seis.sc.edu (Philip Crotwell) Date: Mon, 27 Jun 2011 10:55:47 -0400 Subject: [SAC-HELP] taup_setsac errors in setting theoretical arrival times of phases In-Reply-To: References: Message-ID: Hi What version of TauP are you using? I think this bug has been fixed in the beta version, 2.0beta9 available at http://www.seis.sc.edu/taup/ and so you might want to try that if you still have problems. Philip On Mon, Jun 27, 2011 at 6:58 AM, Alireza Alinaghi wrote: > Dear Friends and Colleagues: > In an attempt to put the theoretical arrival times in SAC headers, I have > used a program contained in TAU_P package, called "taup_setsac". ?I called > this program both within and without SAC environment but I always get the > following error: > SAC> taup_setsac -ph P -evdpkm -verbose GRA1.Z > Exception in thread "main" java.lang.NullPointerException > at edu.sc.seis.TauP.TauP_SetSac.parseCmdLineArgs(TauP_SetSac.java:353) > at edu.sc.seis.TauP.TauP_SetSac.main(TauP_SetSac.java:382) > Does anyone know what goes wrong? Or are there alternative ways to do the > job? > I have SAC 101.4 running on Fedora14 with Java SE ?build 1.6.0_25-b06. > The other TAUP programs run without any error. > Thank you in advance for your hints. > Alireza > _______________________________________________ > sac-help mailing list > sac-help at iris.washington.edu > http://www.iris.washington.edu/mailman/listinfo/sac-help > > From rc202388 at ucla.edu Mon Jun 27 08:48:10 2011 From: rc202388 at ucla.edu (rc202388 at ucla.edu) Date: Mon, 27 Jun 2011 08:48:10 -0700 Subject: [SAC-HELP] Cannot Exit Plot Message-ID: <20110627084810.15941pp7kac1jfi8@mail.ucla.edu> Hello, I am working with SAC currently and when I have a plot open, I cannot close it no matter what. I tried the 'quitsub' command but it is giving me a "sh:quitsub not found" error which is strange because I tried 'fft' and that worked. I am trying to quit the plot because I want to change directory but as long as a plot is open I don't think it will let me. What can I do? Thank you for your help. From mplasencia at ogs.trieste.it Mon Jun 27 09:56:04 2011 From: mplasencia at ogs.trieste.it (Milton P. Plasencia Linares) Date: Mon, 27 Jun 2011 18:56:04 +0200 Subject: [SAC-HELP] Cannot Exit Plot In-Reply-To: <20110627084810.15941pp7kac1jfi8@mail.ucla.edu> References: <20110627084810.15941pp7kac1jfi8@mail.ucla.edu> Message-ID: <20110627185604.18564rkto7ckof1g@webmail.ogs.trieste.it> Hi, Quitsub only works if you had open the sac subprocess: SES Spectral Estimation Subproess, or SSS_ Signal Stacking Subprocess The only way of closing the plot window is running inicm command, but, it delete also your data in memory, and initialize sac for a new session. HTH, Milton ********************************** Milton P. PLASENCIA LINARES Dipartimento Centro di Ricerche Sismologiche Istituto Nazionale di Oceanografia e di Geofisica Sperimentale - OGS Borgo Grotta Gigante 42/C (34010) Sgonico - TRIESTE - ITALIA Tel: +39-040-2140136 Fax: +39-040-327307 E-mail: mplasencia at ogs.trieste.it ASAIN (Antarctic Seismographic Argentinean Italian Network) ********************************* Quoting rc202388 at ucla.edu: > Hello, > > I am working with SAC currently and when I have a > plot open, I cannot close it no matter what. > I tried the 'quitsub' command but it is giving > me a "sh:quitsub not found" error which is strange > because I tried 'fft' and that worked. I am trying to > quit the plot because I want to change directory but > as long as a plot is open I don't think it will let me. > What can I do? > > Thank you for your help. > _______________________________________________ > sac-help mailing list > sac-help at iris.washington.edu > http://www.iris.washington.edu/mailman/listinfo/sac-help > ---------------------------------------------------------------- This message was sent using IMP, the Internet Messaging Program. From snoke at vt.edu Mon Jun 27 10:31:15 2011 From: snoke at vt.edu (Arthur Snoke) Date: Mon, 27 Jun 2011 13:31:15 -0400 (EDT) Subject: [SAC-HELP] Cannot Exit Plot In-Reply-To: <20110627084810.15941pp7kac1jfi8@mail.ucla.edu> References: <20110627084810.15941pp7kac1jfi8@mail.ucla.edu> Message-ID: One way is to enter bd sgf and then follow it with bd x. On Mon, 27 Jun 2011, rc202388 at ucla.edu wrote: > Hello, > > I am working with SAC currently and when I have a > plot open, I cannot close it no matter what. > I tried the 'quitsub' command but it is giving > me a "sh:quitsub not found" error which is strange > because I tried 'fft' and that worked. I am trying to > quit the plot because I want to change directory but > as long as a plot is open I don't think it will let me. > What can I do? > > Thank you for your help. > _______________________________________________ > sac-help mailing list > sac-help at iris.washington.edu > http://www.iris.washington.edu/mailman/listinfo/sac-help From jattanayake at gmail.com Mon Jun 27 12:40:38 2011 From: jattanayake at gmail.com (Januka Attanayake) Date: Mon, 27 Jun 2011 15:40:38 -0400 Subject: [SAC-HELP] SAC with shell script Message-ID: Hi, Is there any possibility that SAC developers could add documentation on calling SAC within a Shell script to the SAC User guide? This is an area I repeatedly had problems with and haven't found a robust solution yet. The external documentation that I have found online haven't been that helpful either. Thank you. Januka. -------------- next part -------------- An HTML attachment was scrubbed... URL: From alireza.alinaghi at gmail.com Tue Jun 28 03:40:09 2011 From: alireza.alinaghi at gmail.com (Alireza Alinaghi) Date: Tue, 28 Jun 2011 12:40:09 +0200 Subject: [SAC-HELP] taup_setsac problem solved by upgrading to TauP-2.0beta9 Message-ID: Dear Colleagues and Friends: The problem I had with taup_setsac was fixed by upgrading from TauP-2.0beta6 (which I had) to TauP-2.0beta9. Thank you all so much for your hints and suggestions. -------------- next part -------------- An HTML attachment was scrubbed... URL: From jattanayake at gmail.com Tue Jun 28 14:59:22 2011 From: jattanayake at gmail.com (Januka Attanayake) Date: Tue, 28 Jun 2011 17:59:22 -0400 Subject: [SAC-HELP] spectrogram time picks Message-ID: Hello, Is there a way to pick times off the spectrogram figure that SAC creates? or is there a way to extract the spectrogram it plots as a matrix so that I can use it to pick times with an external program? I am using SAC 101.4 As a test I tried picks command after spectrogram as follows but it didn't work. r file spectrogram window 1 slice 0.5 order 100 cbar sqrt method mem ymin 0 ymax 2 color picks T3 C T4 C W 0.05 H 0.3 Thanks ! Januka. -------------- next part -------------- An HTML attachment was scrubbed... URL: